Sunday, March 25, 2012

Ebay Selling Fees INCLUDE Shipping

I just thought I would throw this out there.

 In Canada we pay the price of gas, then all local/provincial taxes.  The two are added together and then you pay 5% GST.  So the final price includes you paying tax on a tax.  Nice huh.

Well ebay does the same thing.  Instead of taxing a tax, they charge you a percentage of the shipping cost.  Something you have no control over unless you overcharge. 

When you send someone an invoice through ebay, you include the shipping you charge them.  Ebay takes the final price of your auction PLUS the amount for shipping and then they take their percentage.  So basically you are subsidizing the shipping because Ebay charges you 9% of the shipping cost.  If you try to pass that fee onto the customer, Ebay takes 9% of that too.  So if shipping is $10, its actually costing the seller  $10.90 because Ebay wants $0.90 of the shipping cost.  If you charge your customer $10.90 to cover the 9%, then ebay will get 9% of the $10.90 or $0.98 cents.

Below is a cut and paste right from Ebay.

Total cost to buyer (less any sales tax) Final value fee
(Based on the total amount of the sale, including the cost of the item, shipping, and any other fees a seller may charge, excluding any sales tax)
Item not sold
No fee
$0.01 - $50.00
9.0% of the item’s total cost to the buyer with a maximum charge of $100.00
$50.01 - $1,000
$1,000.01 or more
(based on the total amount of the sale, including the cost of the item, shipping, and any other fees a seller may charge, excluding any sales tax)

This is for Auction style formats.  For Fixed Item Auctions  they charge 11%-13% based on which category you sell in. 
.

Thursday, March 22, 2012

Bumblebee ROCKS!

 This blog wasnt meant to showcase my personal collection, however in light of my current casting burnout, I think its appropriate.
BUMBLEBEE...Everyones favorite Tansformer.  I finally picked up the Masterpiece Movie Edition Bumblebee.  Besides Micronauts I also collect specific Transformers.  In particular the Masterpiece series.  Oddly enough, the Movie Edition Bumblebee is smaller than the Ultimate Bumblebee.  Both are freaking cool, however the Ultimate Bumblebee has issues standing due to its size.  It is the only Transformer (besides Sound wave) that I have opened.  I have other more common Bumblebee's that I open and scatter about the room.

The thing I like most about the Movie Edition Bumblebee is that they put in a display window.  The packaging is a display box.  So you can see whats inside without breaking the seals.

Bumblebee...He Rocks!

Saturday, March 17, 2012

3 3/4" Micronaut Die Cast Repair ***EDITED***

  This post has been edited.  If you already read it, additional information has been added that may cause you to rethink using this method.




Ok...I am cutting this short for now.  But I will document the steps in a later post.  I can and have successfully repaired a vintage diecast chest piece.  But it isnt easy.  In fact...because the metal is so brittle, this is not a repair service I am going to offer.
You drill the tap drill size of the screw you are using right where the cast 'one use' rivet is or would be.  You have to file/grind this flush after you have separated the 2 chest halves.   I went with 3-48 machine screws.  These are specialty screws that had to be ordered.  And the taps are a couple sizes below a standard tap drill set.  You cant just walk in and get them in the hardware section.  I went with the 48 tpi because the hole is so shallow you want as much thread as possible for maximum holding power.  I have a set of rubber soft jaws I use.  Oddly I just fixed my 2 axis vice.  So I can position the piece almost perfectly to where I need it.   Drill the hole being careful not to drill through.  I ground 1 tap flat so I could tap to the dead bottom of the hole maximizing the hole length.  The head of the screw is just small enough it fits in the hole and not so big that it interferes with accessories that one might use the 5 mm hole for.  Believe me...this sounds so much more easier than it really is.

The metal used to make this figures is extremely soft and brittle.  You MUST use soft jaws.  I will post about them in a bit.  These are rubber jaws that slip onto your vice.  But even then, you need just the right tension to hold the piece and not enough to collapse the die cast.  The drilling is the easy part.  Its the tapping that has the potential to wreak havoc on the die cast.

But I must stress that this is a last resort.  These figures are EXTREMELY brittle.  This makes them VERY hard to hold onto.  There is a very real possibility that the cast can crack at any time while drilling or tapping.

In fact just taking them apart can cause them to break.  After years of being stuck together, the die cast body alignment pins can get 'cemented' in to the mating holes and when you try to pry the 2 chest halves apart, they could rip off and stay stuck in the holes or I have seen several where the pelvis gets stuck to the 2 chest halves and working that loose causes the chest pieces to fall apart. Once you have a flaw in the die cast its like a crack in a windshield.  If you take your knuckle and tap on the windshield you can expand and lengthen the crack.  Well once the die cast has an exposed flaw, this compromises the strength of the surrounding material.  And any pressure, like say from a tap or the tightening of a screw could be all it takes to collapse the die cast.

It can be done...Its very tricky...and unless you plan to throw the figure away, use this as a last resort to fixing vintage die cast figures. 

I am going to look into the possibility of maybe using  DEVCON to help strengthen the area around the hole. 

Devcon (I believe that is a trade name) is liquid steel.  When I worked in an automotive shop, we used it to patch motor decks and then they got surface ground.  I want to see if maybe I can use it like a glue and let it dry around the screw.  I would have to drill the hole a little larger, but it would alleviate the pressure applied by the tapping and clamping and would be a much safer approach.

Sunday, March 11, 2012

Riley...Camera Hog

My every other month Riley post.

For those who dont know, Homeworlds Cover Page is my dog Riley.  He loves having his picture taken and you will see pictures here and there where he squeezes into the frame.   Something about the flash and he comes running.    He's my first little dog...but dont tell him he's little.  He still thinks he's a Rotty.  :~)

Thursday, March 8, 2012

Transformers Race Track

I just love the drug store where I get my prescriptions filled.  Its all the way across the city in my old neighborhood, but the drive is always worth it.  they have a very small toy section and there is always something neat there.  I bought an authentic wood Yo Yo 2 weeks ago from there.  I cant believe I didnt have one.

Front
Last week I was in there and they had a Transformers Bumblebee Race Track similar to the Hot Wheels track but with a die cast Bumblebee I havent seen.  Its not a huge track and the set was only $20...How could I say no? 





Back
After humming and hawing about it for a couple of days, I drove to the north side and bought it tonight...

Now the only question is...Should I open it or not?